Complete Assembly; Grass Cutting; Controls Description - Dolmar PM-4660 S1 Manuel D'utilisation

plied), read the relevant owner manuals.
NOTE – The number which precedes each paragraph
links the references in the text to the respective illus-
trations (listed on page III and following pages).

1. COMPLETE ASSEMBLY

NOTE The machine can be supplied with some parts al-
ready assembled.
WARNING! Unpacking and completing the assem-
bly should be done on a flat and stable surface, with
enough space for moving the machine and its packag-
ing, always making use of suitable equipment.
Disposal of the packaging should be done in accord-
ance with the local regulations in force.
1.1a Assembling the handle (Type"I")
Fasten the handle (1) to the chassis brackets with the sup-
plied nuts and bolts (2) as illustrated, making sure the pins
(3) are inserted in the proper holes, bringing the handle to
the right height.
Secure the control cables using the binders (5).
• Manual ignition models
• Electric key ignition models
Assemble the starter cable's guide spiral (4).
1.1b Assembling the handle (Type"II")
Return the handle (1) to the working position and secure it
to the side chassis supports using the supplied nuts and
bolts (2) as illustrated.
The handle (1) can be height-adjusted in three different po-
sitions by inserting the pins (3) in one of the three pairs of
holes on the brackets.
Tighten the thumb knobs (2) securely after adjustment.
Tighten the nut (6) to secure the spiral (5).
• Manual ignition models
• Electric key ignition models
Insert the starter cable (4) to the guide spiral (5).
1.2 Assembling the dashboard (if fitted)
Assemble the dashboard (1) or (1A) following the steps
shown for each type.
With a "1A" dashboard, make sure to correctly fit the knobs
(2-short) and (3-long, if supplied).
1.3 Battery connection
• Electric key ignition models
Connect the battery cable to the general wiring connec-
tor on the lawnmower.
• Electric push-button ignition models
Follow all the instructions provided in the engine
Instruction Manual.

2. CONTROLS DESCRIPTION

NOTE The meanings of the symbols on controls are ex-
plained in the previous pages.
2.1 Throttle lever
The throttle is controlled by the lever (1).
Lever positions are indicated on the relevant plate.
Some models have a fixed speed engine with no need for
a throttle.
2.2 Engine brake lever / cutting means
The cutting means brake is controlled by the lever (1) which
must be held against the handle during ignition and during
lawnmower operations.
The engine stops when the lever is released.
2.3 Drive lever (where applicable)
On power-driven models, push the lever (1) toward the han-
dle for forward movement.
The lawnmower stops moving forward when the lever is
released.
The engine must always be ignited with the drive disen-
gaged.
2.4 Cutting height adjustment
The gearbox (if provided) is controlled by the lever (1),
whose positions are shown on the plate.
2.5a Adjusting the cutting height (Type "A")
The cutting height is adjusted by releasing the lever (1) and
lifting or pressing the chassis to the desired position visible
through the special opening.
DO THIS WHEN THE CUTTING MEANS IS STATIONARY.
2.5b Adjusting the cutting height (Type "B")
The cutting height is adjusted by releasing the button (1)
and lifting or pressing the chassis to the desired position
indicated by the arrow.
DO THIS WHEN THE CUTTING MEANS IS STATIONARY.

3. GRASS CUTTING

NOTE This machine can be used to mow lawns in a
number of different ways; before starting work, prepare the
machine based on how the lawn is to be mowed.
DO THIS WHEN THE ENGINE IS OFF.
3.1 Preparation for mowing and grass collection by
the grass catcher
Raise the rear discharge guard and fasten the grass catch-
er (1 or 2) correctly in place, according to the different pro-
cedures foreseen for each type used.
3.2 Engine ignition
During ignition, follow the instructions in the engine manual
• Manual ignition models
Pull the cutting means brake lever (1) against the handle
and firmly tug the knob on the ignition cable (2).
• Electric key ignition models
Pull the cutting means brake lever (1) against the handle
and turn the ignition key (3).
• Electric push-button ignition models
Insert the consent key (4) firmly in its seat, then pull the
cutting means brake lever (1) against the handle, press
the ignition button (5) and hold until the engine is running.
3.3 Mowing the lawn
The appearance of the lawn will improve if you alternate
cutting in both directions at the same height.
When the grass catcher is too full, grass collection is no
longer efficient and the sound of the lawnmower changes.
To remove and empty the grass catcher,
– stop the engine and wait for the cutting means to stop;
4