Basic Operation; Power On/Off; Volume Control - Jensen Marine MS2013BT Guide D'installation Et D'operation

MS2013BT

BASIC OPERATION

17 12 11 19 13
3
16
1 4 2b
15

Power On/Off

Press any button on the front panel to turn the unit on. Press the power button (1) to turn the
unit on/off.

Volume Control

To increase the volume, press the VOL + button (2a). To decrease the volume, press the
VOL - button (2b).
Mute
Press the MUTE button (17) on the control panel to mute the audio output. Press MUTE again
to restore the audio output to the previous level.
Mode
Press the MODE button (4) on the control panel to select a different mode of operation, as
indicated on the display panel. Available modes include Tuner, iPod, USB, AUX In (optional
Auxiliary Input), BT Audio.
Reset
The reset button should be activated for the following reasons:
• initial installation of the unit when all wiring is completed
• function buttons do not operate
• error symbol on the display
Use a ball point pen or similar object to press the RESET button (19). This may be necessary
should the unit display an error code.
You can recover factory default settings using the RESET function located on the system
menu. With « RESET" flashing, press the ENTER button (18) to activate.
2a
18 20
MS2013BT
14
5 6 7 8 9 10
Audio Menu
Press the AUDIO/MENU button (3) on the control panel to access the audio menu. You can
navigate through the audio menu items by pressing the AUDIO/MENU button repeatedly. Once
the desired menu item appears on the display, adjust that option by pressing the VOL +/-
buttons (2) within 5 seconds. The unit will automatically exit the audio menu after five seconds
of inactivity. The following menu items can be adjusted.
Bass Level
Use the VOL buttons to adjust the Bass level range from "-6" to "+6".
Treble Level
Use the VOL buttons to adjust the Treble level range from "-6" to "+6".
Balance
Use the VOL buttons to adjust the Balance between the left and right speakers from "L12" (full
left) to "R12" (full right).
Fader
Use the VOL buttons to adjust the Fader between the rear and front speakers from "R12" (full
rear) to "F12" (full front).
System Menu
1. Press and hold the AUDIO/MENU button (3) for more than 3 seconds to enter the system
menu. "MENU" will appear on the display, followed by the first menu item, "CONTRAST."
2. Press the SEEK/TUNE/TRK >>| or |<< button (14, 13) or press the AUDIO/MENU button
repeatedly to navigate the system menu and select the desired item.
3. Press the VOL +/- buttons (2) to adjust the selected menu item.
4. Press the AS/PS button (15) to return to the previous operation.
The following items can be adjusted:
• CONTRAST (0 – 10): Set LCD contrast.
• LOW BATT (ON/OFF): Monitor voltage on ACC line.
• DISTANT/LOC: "Local" mode favors access to local stations whose signals are much
stronger, thereby improving reception. Select "Distant" to terminate local receive mode
and resume normal mode.
• AREA (USA/Latin/Europe): Set frequency spacing for various regions.
• VOL PGM (0 – 46): Select an automatic turn-on volume.
• BEEP TONE (ON/OFF): Turn the audible beep ON/OFF (heard when functions/buttons
are selected). NOTE: Beep tone off will not affect LOW BATT audible tone.
• LCD BRIT (0-10): Adjust LCD brightness.
• BT ON/OFF: Choose "BT ON" or "BT OFF".
• BT PAIR (ON/OFF): Choose "YES" to automatically pair a previously paired device.
• BT DEVICE (Lock/Unlock, Disconnect/Connect, Delete): View, lock and delete from a list
of previously paired mobile phone device models.
• RESET: Return the EEPROM to factory default set up values. "RESET" will blink on the
LCD to confirm. Press the ENTER button (18) to select.
NOTE: BT Pair and BT Device menu options are only available while the BT feature is
ON and the radio is in BT Audio mode.
5