Technical Specifications - HK Audio POLAR 10 Manuel D'utilisation

5 Technical Specifi cations
POLAR 10 System
Max. SPL peak calculated 126 dB half space
Frequency response 38 Hz – 20 kHz
+/- 10 dB
Power amp output 2000 W
Amp type Class D – biamped
Crossover frequency 180 Hz, 24 dB/oct.
Active protective circuits Under-voltage, Thermal, Short Circuit, Over-
current Protection; Peak, RMS Limiter
Inputs 2x Balanced XLR/ 1/4" (6.3 mm) combo
jack, 1x Hi-Z instrument jack, 2x RCA/Cinch,
Bluetooth audio stream
Outputs Mix Out
Max. input level +4 dBu
Filter presets Music, Voice, DJ
User presets 5
EQ 3-band, semi-parametric mid EQ
System delay up to 291 ms (100 m)
Bluetooth 5.0
Housing Birch multiplex / ABS
Finish Black 2-component lacquer
Overall system height 213 cm
Weight 26.9 kg / 59.3 lbs
POLAR 10 Subwoofer
Bass woofer 1x 10", 2" voice coil
Front grille 1.5 mm metal grille backed with black
acoustic foam
Dimensions (WxHxD) 36.6 x 62.5 x 54.1 cm
Weight 21 kg / 46.2 lbs
POLAR 10 Mid/High-Unit
Mid speaker 6x 3", 3/4" voice coil, neodymium
HF driver 1x 1", 1" voice coil
Horn directivity 120° x 30°
Front grille 1 mm metal grille backed with black
acoustic foam
Dimensions (WxHxD) 10.8 x 82.5 x 9.8 cm
Weight 3.9 kg / 8.6 lbs
POLAR 10 Spacer
Front grille 1 mm metal grille backed with black
acoustic foam
Dimensions (WxHxD) 10.8 x 82.5 x 9.8 cm
Weight 2 kg / 4.4 lbs
General Technical Specifi cations
Current consumption 0.6 A / 220-240 V AC
pursuant to EN 62368-1 0.8 A / 100-120V AC
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any
use of such marks by Stamer Musikanlagen GmbH is under license.
All mentioned trademarks and copyrights belong to their respective owners.
For the USA:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
End users must follow the specific operating instructions for satisfying RF exposure compliance. This
transmitter meets both portable and mobile limits as demonstrated in the RF Exposure Analysis. This
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter
except in accordance with FCC multi-transmitter product procedures.
For Canada:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of
a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce
potential radio interference to other users, the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful
communication.
POLAR 10 1.1
9