Intended Use; Scope Of Supply; Product Overview; Before You Begin - Chamberlain ML810EV Notice De Montage Et De Commande

2

Intended use

The device is intended for the opening and closing of garage doors (please
refer to section 6 "Door Types")� The device is not meant for commercial
use but solely for the use in private garage doors that are appropriate for a
single household� Any improper use of the drive could increase the risk of
accidents� The manufacturer assumes no liability for such usage� Only the
original accessories of Chamberlain may be connected to the drive� With this
drive, automated gates must comply with the currently valid international and
country-specific standards, guidelines and regulations (among other things,
EN 13241, EN 12453 and EN 12604)�
3

Scope of supply

Please check the supplied parts for completeness before starting the in-
stallation� Note: The numbering only applies to the corresponding section�
Parts overview:
1� Drive head
2� Remote control
3� Rail bracket
4� Hardwarebag
5� Wireless Wall Control
(ML810EV)
6� Header bracket
7� Door bracket
Hardwarebag:
Truss head screw
15�
6 x 80 mm
16� Lock nut M6
17� Hexagonal head screw
18� Nut M6
19� Bolt
4

Product overview

This figure always offers you a complete overview of the readyassem-
bled system during the step by step installation of the system�
a� Header bracket
b� Belt
c� Rail
d� Carriage
e� Connecting piece
f� Rail bracket
g� Hanging bracket
1x 8� Adapter for gear wheel
2x 9� Curved door arm
2x 10� C-bracket
1x 11� Hanging bracket
1x 12� Rail
1x 13� MyQ Starter Kit
(ML810EV-Smart)
(ML1040EV-Smart)
1x 14� Photocells
(ML1040EV)
1x 20� Safety cotter pin
1x 21� Screw ST 6 x 60 mm
4x 22� Screw ST 6,3 x 20 mm
4x 23� Plug
1x
h� Power cable
i� Drive head
j� Release
k� Straight door arm
l� Curved door arm
m� Door bracket
5

Before you begin

IMPORTANT NOTE
If your garage does not have a side entrance, an external emergency
release should be installed� This allows for manual operation of the
garage door from the outside during power failure�
6

Door Types

A� One-Piece Door with Horizontal Track Only�
B� One-Piece Door with Horizontal and Vertical Track – Special door
arm (E, The Chamberlain Arm™) and the Protector System™
required� See your dealer�
C� Sectional Door with Curved Track – See 20B – connect door arm�
D� Canopy door – Special door arm (E, The Chamberlain Arm™) and
the Protector System™ required� See your dealer�
E� The Chamberlain Arm™ for use on door types B and D�
1x
7

Preparation

1x
First, check whether your door is balanced and in equilibrium�
2x
Open your door about halfway and let it go�
2x
The door can now hardly change its position independently,
1x
but must remain in this position held by the spring force alone�
1� The rail of the garage door MUST be connected securely and firm-
1x
ly to the supporting wall or ceiling above the garage door�
1x
2� Additional brackets and mounting rails (not included in the supply)
might be required, if the your garage ceiling has a cladding, boards
1x
or similar�
3� If your garage does not have a separate side entrance, an external
emergency release (refer to section 34 "Optional Accessories")
must be installed�
1x
8

Tools required

4x
Tool list:
8x
4x
Ladder
Marking pen
Pliers
Drilling machine
Hammer
Ratchet 10 mm / 13 mm
Hacksaw
Different drill bits for concrete
and (or wood (8, 6, 5, 4�5 mm)
Box wrench
Water level
Screwdriver
Measuring tape
en 4