Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Location Requirements
To ensure proper ventilation for your ice maker, the front side
must be completely unobstructed. The ice maker may be
closed in on the top and three sides, but the installation
should allow the ice maker to be pulled forward for servicing
if necessary.
Installation of the ice maker requires a cold water supply inlet
of ¹⁄₄" (6.35 mm) O.D. soft copper tubing with a shut-off valve
or a Whirlpool supply line Part Number 8212547RB, and a
Whirlpool approved drain pump, Part Number 1901A, only to
carry the water to an existing drain.
Choose a well-ventilated area with temperatures above 55°F
(13°C) and below 110°F (43°C). Best results are obtained
between 70°F and 90°F (21ºC and 32°C).
The ice maker must be installed in an area sheltered from
the elements, such as wind, rain, water spray, or drip.
When installing the ice maker under a counter, follow the
recommended opening dimensions shown. Place electrical
and plumbing fixtures in the recommended location as
shown.
NOTES:
Check that the power supply cord is not damaged,
pinched, or kinked between the ice maker and the
cabinet.
Check that the water supply line is not damaged,
pinched, or kinked between the ice maker and the
cabinet.
Check that the drain line (on some models) is not
damaged, pinched, or kinked between the ice maker and
the cabinet.
Check that the ice maker door is not flush with the
standard cabinets to avoid problems with opening the ice
maker door.
34"
(86.4 cm)
Min.
¹⁄₂
34
"
(87.6 cm)
Max.
3
(8.9 cm)
24"
(60.1 cm)
A. Recommended location for electrical and plumbing fixtures
B. Floor level
Choose a location where the floor is even. It is important for
the ice maker to be level in order to work properly. If needed,
you can adjust the height of the ice maker by changing the
height of the leveling legs. See "Leveling."
4
¹⁄₂
11
"
(29.2 cm)
28
(72.4 cm)
¹⁄₂
9"
"
(22.9 cm)
15"
(38.1 cm)
Electrical Requirements
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Before you move your ice maker into its final location, it is
important to make sure you have the proper electrical
connection:
A 115-volt, 60 Hz., AC-only, 15- or 20-amp electrical supply,
properly grounded in accordance with the National Electrical
Code and local codes and ordinances, is required.
It is recommended that a separate circuit, serving only your ice
maker, be provided. Use a receptacle which cannot be turned off
by a switch or pull chain.
IMPORTANT:If this product is connected to a GFCI (Ground
Fault Circuit Interrupter) equipped outlet, nuisance tripping of the
power supply may occur, resulting in loss of cooling. Ice quality
may be affected. If nuisance tripping has occurred, and if the
condition of the ice appears poor, dispose of it.
RecommendedGroundingMethod
The ice maker must be grounded. The ice maker is equipped with
a power supply cord having a 3 prong grounding plug. The cord
must be plugged into a mating, 3 prong, grounding-type wall
receptacle, grounded in accordance with the National Electrical
A
Code and local codes and ordinances. If a mating wall receptacle
is not available, it is the personal responsibility of the customer to
have a properly grounded, 3 prong wall receptacle installed by a
¹⁄₂
qualified electrician.
"
B
WARNING
Electrical Shock Hazard
Publicité
Table des Matières
