Oleo-Mac GS 180 E Manuel D'installation Et D'entretien page 25

wrench or a key left attached to a rotating
part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing
and balance at all times. This enables
better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) I f d e v i ce s a re p rov i d e d fo r t h e
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of
these devices can reduce dust-related
hazards.
4) Power tool use and care
a) Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better
and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch
does not turn it on and off. Any power
tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power
s o u r c e b e f o r e m a k i n g a n y
adjustments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of starting
the power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tool's operation. If damaged, have the
power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to bind
and are easier to control.
g) Use the power tool, accessories and
tool bits etc., in accordance with these
i n s t r u c t i o n s a n d i n t h e m a n n e r
intended for the particular type of
power tool, taking into account the
working conditions and the work to be
performed. Use of the power tool for
operations different from intended could
result in a hazardous situation.
5) Service
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
Chain saw safety warnings:
• Keep all parts of the body away from the
saw chain when the chain saw is operating.
Before you start the chain saw, make sure
the saw chain is not contacting anything. A
moment of inattention while operating chain
saws may cause entanglement of your clothing
or body with the saw chain.
• Always hold the chain saw with your right
hand on the rear handle and your left hand
on the front handle. Holding the chain saw
with a reversed hand configuration increases
the risk of personal injury and should never be
done.
• Hold the power tool by insulated gripping
surfaces only, because the saw chain may
contact hidden wiring or its own cord. Saw
chains contacting a "live" wire may make
exposed metal parts of the power tool "live"
and could give the operator an electric shock.
• We a r s a f e t y g l a s s e s a n d h e a r i n g
protection. Further protective equipment
f o r h e a d , h a n d s , l e g s a n d f e e t i s
recommended. Adequate protective clothing
will reduce personal injury by flying debris or
accidental contact with the saw chain.
• Do not operate a chain saw in a tree.
Operation of a chain saw while up in a tree may
result in personal injury.
• Always keep proper footing and operate
the chain saw only when standing on fixed,
secure and level surface. Slippery or unstable
I
GB
F
D
E
SK
P
GR
TR
CZ
RUS
UK
PL
23