Warranty Exclusions - Troy Lee Designs SE4 Mode D'emploi

REMOVAL AND INSTALLATION OF STRAP COVERS:
Strap Covers are held in place by use of a single snap located on the bottom side of strap near the base of the cover
inside the helmet. See Fig.A
Cheek Pads must first be removed to get access to the snap.
With helmet bottom side up, reach through eye port and place index finger behind snap.
Lift and pull strap towards you
When reinstalling carefully align snap then press until you hear a click.
REMOVAL AND INSTALLATION OF HEAD LINING:
Head lining is attached by use of four (4) snaps at rear and and front
sides of interior. See Fig.D
To remove: Pull at each snap location, inward until snaps disengage.
To install: Place liner inside helmet and line up all four (4) snaps.
Firmly press on each snap seperately until you hear a click. Take care to
line up male snap with female snap hole before pressing.
- Helmets are energy absorbing devices intended to deform, fracture, crush, and collapse as they absorb energy
generated by an impact. The SE4 helmet should be treated /handled carefully so that it will have all the available
energy absorbing materials if you should ever need them. Your adult size Air helmet will give you years of good
service if properly cared for.
- Never decorate your helmet with paint, decals, stickers or tape. Use only mild soap and water to clean the outside
or inside of your helmet and the pads. Chemicals used in many cleaners can be harmful to the outer shell of your
helmet. Frequently, this damage is not visible, and can result in premature fracturing of the shell when impacted.
- Use only mild soap and water to clean the interior of your helmet. All of our models have removable liner. These
liners can be washed by hand in a bucket with mild soap and water, rinsed, then air dried only. Remove odors by
rinsing with a solution of bicarbonate of soda and water. Never use an oven or other heating source to dry the
helmet. Temperatures in excess of 130F degrees can damage the energy absorbing inner liner. Do not allow the
helmet to sit in a closed vehicle or in direct sunlight on hot day as temperatures can exceed 130F degrees. Never
allow your helmet to come in contact with gasoline or other petroleum products, as this will cause serious damage to
the energy absorbing liner and/or the outer shell of the helmet.
- Troy Lee Designs helmets should not be painted by anyone other than Troy Lee Designs. Many helmet components
can be seriously damaged by chemicals and/or solvents contained in most paint or by careless handling during the
repair process. Do not sand or use any abrasive material on the helmet.
SE4 HELMET WARRANTY: Troy Lee Designs warrants to the original retail purchaser ("you") that the Troy Lee
Designs product for which they received this warranty is free from defects in material and workmanship for FIVE
years from the date of original retail purchase. This warranty is not transferable to a subsequent purchaser. Troy Lee
Designs sole obligation under this warranty is to repair or replace the product, at Troy Lee Designs option. Troy Lee
Designs must be notified in writing of any claim under this warranty within 60 days of any claimed lack of conformity
of the product.
WARRANTY LIMITATIONS: The duration of any implied warranty or condition, of merchantability, fitness for a
particular purpose, or otherwise, on this product shall be limited to the duration of the express warranty set forth
above. In no event shall Troy Lee Designs be liable for any loss, inconvenience or damage, whether direct, incidental,
consequential or otherwise, resulting from breach of any express or implied warranty or condition, of merchantabili-
ty, fitness for a particular purpose, or otherwise with respect to this product, except as set forth herein. Some
states or countries do not allow limitation on how long an implied warranty lasts and some do not allow exclusions or
limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights, which may vary, from location to
location. This warranty will be interpreted pursuant to the laws of the United States. This warranty will be
interpreted pursuant to the laws of the United States. The original English language version/meaning of this
warranty controls over all translations and Troy Lee Designs is not responsible for any errors in translation of this
warranty or any product instructions. This warranty is not intended to confer any additional legal, jurisdictional or
warranty rights to you other that those set forth herein or required by law.
CARE
If any portion of this warranty is held to be invalid or unenforceable for any reason, such finding will not invalidate
any other provision. For products purchased in countries other than the United States please contact Troy Lee
Designs authorized distributor in that respective country.
(Fig.D)
TO OBTAIN SERVICE UNDER THIS WARRANTY YOU MUST EITHER: Bring or send your Troy Lee Designs SE4
Helmet together with this warranty, the retail seller's original receipt or other satisfactory proof of the date of
purchase to the retailer where you purchased the item. You can also send your Troy Lee Designs Air Helmet (with the
return authorization number on the outside of the shipping container and affixed to the product), together with the
retail seller's original receipt or other satisfactory proof of the date of purchase to: Troy Lee Designs Attn: Helmet
Warranty Dept., 155 East Rincon. Corona, CA 92879 USA. You must obtain a return authorization number by calling
Troy Lee Designs, at (951)371-5219 or sending an E-mail to warranty@troyleedesigns.com prior to returning the
product to Troy Lee Designs. Any postage, insurance or shipping cost incurred in sending your Troy Lee Designs
product for service under either option above is your responsibility. Troy Lee Designs will not be responsible for
products lost or damaged in shipping. For products purchased in countries other than the United States please
contact the Troy Lee Designs authorized distributor in the country where the product was purchased. They can be
found on our website at www.troyleedesigns.com Troy Lee Designs may require that you complete and sign a
warranty replacement request form before processing your warranty claim.
CRASH REPLACEMENT POLICY: Troy Lee Designs understands that accidents will happen. As a result, Troy Lee
Designs will assist with the replacement of your helmet by providing a 30% discount off of Troy Lee Designs current
suggested retail price in your respective country. All other provisions of this warranty apply and the procedures
outlined for warranty service apply also to the accident replace- ment policy. Troy Lee Designs will make the final
decision on whether the part will be covered under the crash replacement policy.
WARRANTY EXCLUSIONS: Retailers and sellers of Troy Lee Designs products are not authorized to modify this
warranty in any way. It is your responsibility to regularly examine the product to determine the need for normal
service or replacement. This warranty does not cover the following:
- Products that have been modified, neglected or poorly maintained, used for commercial purposes, misused or
abused or involved in accidents.
- Damage occurring during shipment of the products (such claims must be presented directly to the shipper).
- Damage to products resulting from improper assembly or repair, the use or installation of parts or accessories not
compatible with the original intended use of the product, or the failure to follow the product warnings and usage
instructions.
- Damage or deterioration to the surface finish, aesthetics or appearance of the product.
- The labor required to remove and/or re-fit and re-adjust the item covered by this warranty.
- Normal wear to the product.
- Any products for which the consumer does not follow the warranty procedures outlined above. For the current
version of this warranty please visit our website at www.troyleedesigns.com
Helmet specifications are subject to change without notice.
(© 2015 Troy Lee Designs)
WARRANTY
EN