Boss eBand JS-10 Mode D'emploi page 35

Masquer les pouces Voir aussi pour eBand JS-10:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 92
NS (Noise Suppressor)
This effect reduces the noise and hum picked up by guitar pickups .
Since it suppresses the noise in synchronization with the envelope
of the guitar sound (the way in which the guitar sound decays over
time), it has very little effect on the guitar sound, and does not
harm the natural character of the sound .
Parameter/
Explanation
Range
ON/OFF
OFF, ON
Turns the NOISE SUPPRESSOR effect on/off .
THRESHOLD
Adjust this parameter as appropriate for the volume of
the noise .
If the noise level is high, a higher setting is appropriate .
If the noise level is low, a lower setting is appropriate .
Adjust this value until the decay of the guitar sound is as
0–100
natural as possible .
* High settings for the threshold parameter may result
in there being no sound when you play with your
guitar volume turned down .
EQ (Equalizer)
This adjusts the tone as a equalizer . A parametric type is adopted
for the high-middle and low-middle range .
Parameter/
Explanation
Range
ON/OFF
OFF, ON
Turns the EQUALIZER effect on/off .
LOW GAIN
-20–+20dB
Adjusts the low frequency range tone .
HIGH GAIN
-20–+20dB
Adjusts the high frequency range tone .
LEVEL
-20–+20dB
Adjusts the overall volume level of the equalizer .
LO-MID FREQ (Low Middle Frequency)
Specifies the center of the frequency range that will be
20 .0Hz–10 .0kHz
adjusted by the LO-MID GAIN .
LO-MID Q (Low Middle Q)
Adjusts the width of the area affected by the EQ
centered at the LO-MID FREQ .
0 .5–16
Higher values will narrow the area .
LO-MID GAIN (Low Middle Gain)
-20–+20dB
Adjusts the low-middle frequency range tone .
HI-MID FREQ (High Middle Frequency)
Specifies the center of the frequency range that will be
20 .0Hz–10 .0kHz
adjusted by the HI-MID GAIN .
HI-MID Q (High Middle Q)
Adjusts the width of the area affected by the EQ
centered at the HI-MID FREQ .
0 .5–16
Higher values will narrow the area .
HI-MID GAIN (High Middle Gain)
-20–+20dB
Adjusts the high-middle frequency range tone .
LOW CUT (Low Cut Filter)
This sets the frequency at which the low cut filter begins
to take effect .
FLAT, 20Hz–
800Hz
When "FLAT" is selected, the low cut filter will have no
effect .
HIGH CUT (High Cut Filter)
This sets the frequency at which the high cut filter
630Hz–12 .5kHz,
begins to take effect . When "FLAT" is selected, the high
FLAT
cut filter will have no effect .
MODULATION
Use MOD SELECT to select the effect that you want to use .
Parameter/
Explanation
Range
ON/OFF
OFF, ON
Turns the MODULATION effect on/off .
MOD SELECT (Modulation Select)
Select the modulation type .
PHASER
Phaser
FLANGER
Flanger
CHORUS
Chorus
TREMOLO
Tremolo
ROTARY
Rotary
UNI-V
Uni-Vibe
PAN
Pan
PHASER
By adding varied-phase portions to the direct sound, the phaser
effect gives a whooshing, swirling character to the sound .
Parameter/
Explanation
Range
TYPE
Selects the number of stages that the phaser effect will use .
This is a four-phase effect . A light phaser effect is
4 STAGE
obtained .
8 STAGE
This is an eight-phase effect . It is a popular phaser effect .
This is a twelve-phase effect . A deep phase effect is
12 STG
obtained .
This is the phaser with two phase shift circuits
BI-PH .
connected in series .
RATE
0–100 (*)
This sets the rate of the phaser effect .
DEPTH
0–100
Determines the depth of the phaser effect .
RESONANCE
Determines the amount of resonance (feedback) .
0–100
Increasing the value will emphasize the effect, creating
a more unusual sound .
Setting parameters with Tap Tempo
The values for the parameters marked with an asterisk (*) can
be set so they match the timing you use when pressing the
[SPEED] button (Tap Tempo) .
Tap the [SPEED] button two or more times in succession to
specify a tempo for the parameter .
Appendices
p . 33
p . 34
p . 34
p . 34
p . 34
p . 34
p . 34
33

Publicité

Table des Matières
loading

Table des Matières