Before Starting The Equipment - Hurricane HLS 230 Mode D'emploi

Anleitung_HLS_230_SPK7:_

5. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making
adjustments to the equipment.
5.1 Fitting the suction tube (Fig. 3a-3d.)
First plug together the front suction tube (1) and the
rear suction tube (2). (Fig. 3a). Screw the two pipes
together with the special screws (Fig. 3b/Item 10).
Then please insert the suction tube into the motor
housing (Fig. 3c) and screw together with the special
screws (Fig. 3d/Item 10).
Note: Do not disassemble the suction tube any
more once it has been assembled.
5.2 Fitting the debris bag (Fig. 3e-3f)
First, hang the eyelet up on the appropriate hook on
the suction tube (Fig. 3e). Then slip the debris bag
(Fig. 3f/Item 7) over the port on the motor housing.
Make sure that there is an audible click when they
engage.
5.3 Assembly of carrying strap (Fig. 3g)
Push the carrying strap (Fig. 2/Item 4) through the
metal inserts as shown in Fig. 3g and close the quick
fasteners.
Start up the tool only after it is fully assembled.
Always inspect the tool power cord for damage
before starting up. The tool may only be used if the
cord is in flawless condition.
6. Operation
6.1 Sizing the strap (Fig. 1)
Size the length of the carrying strap (4) so that the
vacuum tube just clears the ground. The guide rollers
(9) at the bottom end of the suction tube will help you
to maneuver the suction tube on the ground.
6.2. Adjusting the additional handle (Fig. 4)
Unfasten the star nut (Fig. 4/Item A), turn the
additional handle into the desired position and re-
tighten the star nut (Fig. 4/Item A).
18.03.2009 15:25 Uhr Seite 13
6.3 Connecting up the machine and switching it
on. (Fig. 5.6)
The appliance can be connected to any mains socket
with no less than a 10A fuse (with 230V alternating
voltage). The Socket must be fused with an earth-
leakage circuit breaker (FI). The release current must
not be higher than 30mA.
b Insert the connector plug into the clutch of the
power cable (extension cable).
b Secure the power cable with the cable strain-
relief clamp as shown in the picture.
b To switch on, switch the ON/OFF switch (Fig.
6/Item 5) to "I".
To switch off, switch the ON/OFF switch (Fig.
b
6/Item 5) to "0".
6.4 Selecting the mode of operation
6.4.1 Suctioning (Fig. 7)
b Turn the lever (Fig. 7/Item 8) to position B. You
can do this both when the device is at a standstill
and while it is running.
6.4.2 Blowing (Fig. 7)
b Turn the lever (Fig. 7/Item 8) to position C. You
can do this both when the device is at a standstill
and while it is running.
b Channel the air stream forward and walk slowly
to blow foliage or garden refuse into a pile or to
clear out hard-to-reach places.
b Important!
Empty the debris bag before blowing.
Otherwise, the material that has been
vacuumed up could drop out.
6.5 Emptying the debris bag and pre-screen
(Fig. 1)
Empty the debris bag (7) in good time. When the bag
is heavily loaded with material, vacuum power is
considerably reduced. Deposit organic refuse at a
compost site.
b Switch off the tool and pull out the plug.
b Open the zipper on the debris bag (7) and
shake out the material.
b Close the zip on the debris bag (7) again.
GB
13