Intended Use; Safety Instruction; General Notes; Basic Functions - ARRI L Série Guide Rapide

Masquer les pouces Voir aussi pour L Série:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

Intended use

This product is intended to illuminate persons and objects.
Always follow the safety information.
Any usage other than described above is not permitted and can damage
the product and lead to associated risks such as short-circuit, fire, elec-
tric shock, etc. You are not allowed to modify the product.

Safety Instruction

READ THE INSTRUCTIONS
Read all instructions carefully before installing, using or
servicing the product. Refer to the ARRI website
www.arri.com for the latest documentation.
NOT FOR RESIDENTIAL USE
Not to be used in residential areas. The luminaire is
intended for professional use only. The fixture may only be
operated by qualified persons.
DANGER OF LIFE!
CAUTION - RISK OF ELECTRICAL SHOCK!
Do not open the housing of the fixture. For safe operation,
the housing must be completely closed at all times.
DISCONNECT ELECTRICALLY!
Disconnect electrically before re-lamping or carrying out
any service or maintenance work or when the product is not
in use.
Always earth the fixture electrically. Only use TN- or TT one phase
power supplies and a power plug according to IEC 60309-1 or a
similar national standard.
Use suitable, genuine ARRI mains cables only. The use of third-
party mains cables is on your own risk.
Always follow the instructions of the connector manufacturer when
installing a connector on the mains cable.
Do not use any cable to hold, move or suspend the device.
Check the mains cable prior to every operation for damage.
In case of visible damage to cables or housings, the device may not
be operated any longer. Damaged components of the housing
must be replaced by a certified ARRI service center.
Do not cover the ventilation slots of the device. Unobstructed air-
flow is required for effective cooling.
Avoid direct illumination by other luminaires or other heat sources.
CAUTION - HOT SURFACE! RISK OF BURNING!
The fixture or parts of the fixture become hot during opera-
tion. Touch hot parts only with protective gloves.
CAUTION - OPTICAL RADIATION!
The fixture emits optical radiation such as UV, visible
radiation, IR during operation. Always observe the
minimum distance to persons and objects. Observe the
information about the photobiological hazards and risk
group.
CAUTION – HIGH BEAM INTENSITY!
RISK OF EYE INJURY!
Do not stare into the operating light source of the
fixture.
REPLACE DAMAGED COMPONENTS
Replace any cracked or scratched protective
shields such as lenses, UV-screens, diffusions or
housing parts immediately. Do not use a product
with broken parts. The luminaire shall only be
used complete with its protective shield.
4
Always observe the minimum distances to persons and flammable ob-
jects given on the type plate. Always observe the
maximum tilt angle.
L5 / L7

General Notes

Observe all common and local safety regulations.
Please keep these instructions for possible subsequent
owners.
Please dispose the packing material at your local recycling center
for environmental protection.
Defective products shall be disposed appropriately. For further in-
formation please ask your ARRI dealer or your local
authorities.
Use only original ARRI spare parts and accessories.
To Secure the Device and its Accessories
When mounted in a hanging position or above persons, use a suit-
able safety cable to prevent the luminaire and the
attached accessories against falling when the primary mounting
method fails.
The safety cable and its connecting elements must be rated at a
minimum load of 10 times the weight of the device and all attached
accessories.
Lead the safety cable through the stirrup (2) and the structure the
device is mounted to.
The safety cable must be kept short.
The accessories must be inserted correctly in the accessory hold-
ers. The top latch (4) must be closed and the safety catch (5) must
be engaged.
Tripods must be set up in a stable way and must be rated to carry
the required load. Please observe the weight of the
accessories and the cables. Please refer also to the leaflet
„Operating your ARRI Lampheads Safely" L5.40731.E.
The L-Series must be mounted on its yoke (2) in perpendicular
standing position or hanging position. Never apply lateral load to
the stirrup as components may break.

Basic Functions

MOUNTING
Always insert the 28 mm spigot (1) into the bushing of a suitable stand
or a suitable clamping system and fix and secure the spigot afterwards.
PAN AND TILT
Swivel the luminaire after loosening the screw of the stand or the clamp-
ing system. The tilt angle can be adjusted by releasing the tilt lock (3).
After the adjustment of the pan angle and the tilt angle, the screws re-
spectively clamp must be fastened again.
TO ADJUST THE BEAM ANGLE
The beam angle can be continuously adjusted by turning the
focus knob (6). In doing so, the lens tube will move into and out of the
housing. This mechanism has two protective functions:
A predetermined breaking point protects the luminaire from dam-
age if the focus knob is being turned with overly strong force.
Therefore only turn the focus knob by hand and stop when the lens
tube has reached full extension or retraction!
A self-inhibiting gear avoids the inadvertent movement of the lens
tube when the luminaire is in a tilted position.
L10

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

L5-c manL5-c p.o.L7 manL7 p.o.L10 manL10 p.o.

Table des Matières