Before Starting The Equipment - Scheppach HBS30 Série Traduction Des Instructions D'origine

• Adjustable protective devices have to be adjusted
as close as possible to the work piece.
• Important! Support long work pieces (e.g. with a roll-
er table) to prevent them sagging at the end of a cut.
• Make sure the blade guard (4) is in its lower posi-
tion when the saw is being transported.
• Safety guards are not to be used to move or misuse
the machine.
• Blades that are misshapen or damaged in any way
must not be used.
• If the table insert is worn, replace it.
• Never operate the machine if either the door pro-
tecting the blade or the detachable safety device
are open.
• Ensure that the choice of blade and the selected
speed are suitable for the material to be cut.
• Do not begin cleaning the blade until it has come to
a complete standstill.
• For straight cuts of small work pieces against the
longitudinal limit stop the push stick has to be used.
• Wear gloves when handling the saw blade and
rough materials
• The band saw blade guard should be in its lowest
position close to the bench during transport.
• For miter cuts when the table is tilted, the parallel
stop must be positioned on the lower part of the
table.
• Never use guards to lift or transport items.
• Ensure that the band saw blade guards are used
and correctly adjusted.
• Keep your hands a safety distance away from the
band saw blade. Use a push stick for narrow cuts.
• The push stick has to be stored on the intended de-
vice, so that it can be reached from normal working
position and is always ready to be used.
• In the normal operating position the operator is in
front of the machine.
m WARNING! This electric tool generates an elec-
tromagnetic field during operation. This field can im-
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat-
ing the electric tool.
Remaining hazards
The machine has been built using modern technology
in accordance with recognized safety rules. Some re-
maining hazards, however, may still exist.
• Risk of injury for fingers and hands by the rotat-
ing saw band due to improper handling of the work
piece. Risk of injury through the hurling work piece
due to improper handling, such as working without
the push stick.
• Risk of damaging your health due to wood dust and
wood chips. Wear personal protective cloth such as
goggles. Use a fitting dust extractor.
• Risk of injury due to defective saw band. Regularly
check saw band for such defects.
• Risk of injury for fingers and hands while changing
saw band. Wear proper gloves.
• Risk of injury due to starting saw band while switch-
ing on the machine.
• The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
26 GB
• Wear only close fitting clothes. Remove rings,
bracelets and other jewelry.
• For the safety of long hair, wear a cap or hair net. Even
when all safety measures are taken, some remaining
hazards which are not yet evident may still be present.
• Remaining hazards can be minimized by follow-
ing the instructions in „General safety instructions"
„Proper Use" and in the entire operating manual.
6. Technische Daten
Electro motor
Power
Revolutions n0
Saw band length
Saw band width
Saw band width max.
Cutting speed
Passage height
Passage width
Table size
Table size with min.
extension
Table size with max.
extension
Slewing range of the
table
Max. size of the workpi-
ece
Overall weight
Subject to technical modifications!
* Operating mode S1, continous operation.
The work piece must have a minimum height of 3 mm
and a minimum width of 10 mm.
The total noise values determined in accordance
with EN 61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection!
The effects of noise can cause a loss of hearing.
Keep the noise level and vibration to a minimum!

7. Before starting the equipment

Make sure the machine stands securely, i.e. bolt it to
a workbench or solid base. There are two holes for
this purpose in the machine foot.
• The saw table must be mounted correctly.
• All covers and safety devices have to be properly
fitted before the machine is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws etc.
• Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
230 - 240 V ~ 50 Hz
S1 250W, S2 30 min
350W
1400 min
-1
1400 mm
3,5-12 mm
12 mm
900 m/min
0 - 80 mm
200 mm
300 x 300 mm
380x300mm
535x300mm
0° bis 45°
400 x 400 x 80 mm
19 kg
77,4 dB(A)
3 dB
90,4 dB(A)
3 dB