Ps15 & Ls1200 : Specifications, Curves & Diagrams - Nexo PS Série Manuel D'utilisation

P.36
___________________________________________________________________________________________________
PS15 & LS1200 : SPECIFICATIONS, CURVES & DIAGRAMS
SYSTEM SPECIFICATIONS
Frequency Response [a]
Usable Range @-6 dB [a]
Sensitivity 1W @ 1m [b]
Nominal Peak SPL @ 1m [b]
HF Dispersion [c]
Directivity : Q & DI [c]
Crossover Frequencies
Nominal Impedance
Recommended Amplifiers
SYSTEM SPECIFICATIONS
Frequency Response
Sensitivity 1W @ 1m
Nominal Peak SPL @ 1m
Cutoff Frequency
Nominal Impedance
Recommended Amplifiers
SYSTEM OPERATION
Electronic Controller
Dispersion configuration
SubBass
Speaker Cables
PRODUCT FEATURES
Components :LF [Sub]
HF
Height x Width x Depth
Weight : Net
Speakon Connectors
Construction
Fittings: Handles
Front finish
Flying Points
Stand fittings
PS SERIES MANUAL REV3 10/10/05
PS15 & LS1200 : SPECIFICATIONS, CURVES & DIAGRAMS
PS15 with PS15 TDcontroller MK2
50 Hz - 18 kHz ±3 dB
47 Hz - 18 kHz
102 dB SPL Nominal. 99 dB SPL Wideband
131 to 134 dB Peak (for 550 to 1200 W RMS Amp.)
50° to 100° Hor. x 55° Vert. Rotatable Horn - 4 positions
Q : 16 Nominal DI : 12 dB Nominal
900 Hz Passive or Active (internally switchable)
Passive : 8 Ohms or Active : LF : 6 Ohms & HF : 8 Ohms
550 to 1200 Watts into 8 Ohms for 1 x PS15 per channel
1000 to 1800 Watts into 4 Ohms for 2 x PS15 per channel
PS15Bass with PS15 TDcontroller
40 Hz - 300 Hz
102 dB SPL Nominal. 99 dB SPL Wideband
131 to 134 dB Peak (for 550 to 1200 W RMS Amp)
120 Hz Passive - 6dB per Octave - Reactance compensation
8 Ohms
550 to 1200 Watts into 8 Ohms for 1 x PS15Bass per channel
1000 to 1800 Watts into 4 Ohms for 1 x PS15Bass + 1 x PS15 or 2 x PS15Bass per channel
The PS15 TDcontroller is precisely matched to the PS15 & LS1200 cabinets and includes protections. Using
PS15 & LSub's without a properly connected PS15 TD will result in poor sound quality and can damage the
components.
After quick-release of the front grille from its fixings, the HF Horn can be rotated in 4 positions for dispersion
configuration.
The PS15 can be used without optional Subbass. Active operation of the LS1000 is included in the PS15 TD.
PS15 are wired 2- & 2+ on Passive Input Speakons, LS1000 on 1- & 1+. Loop through Speakons are present
on both. Single identical cables can thus be used to loop through combinations of PS15 in passive & LS1000 in
no particular order.
PS15
1 x 15" (38 cm) 6 Ohms proprietary
1 x 2" throat, 3" Titanium diaphragm, driver + Low Distortion,
Constant Directivity Asymmetrical Dispersion Horn.
675 x 434 x 368 mm (26.57"x 17.08"x 14.48")
29 kg (64 Lb.)
2 x 4 pole (Passive In & Loop Thru) + 1 x 4 Pole (Active In)
Baltic Birch Ply finished with structured black coating
2 Metal recessed pockets
Acoustic foam on hex perforated steel grille (77%
transparent)
1 steel anchor plate for flying track on top (9 positions).
2 steel anchor plates for flying tracks on bottom (3 positions)
Built in Steel Stand Fitting, 35 mm (1"3/8)
LSub 1200 with PS15 TDcontroller MK2
30 Hz - 120 Hz ±3 dB
29 Hz - 130 Hz
102 dB SPL Nominal
133 to 135 dB Peak (800 to 1200 W RMS
Amp.)
-
( f > 1.5 kHz ) -
80 Hz Active through PS15 TD
6 Ohms
800 to 1200 Watts into 8 Ohms
-
LSub 1200
1 x 18" (46 cm) long excursion 6 Ohm
proprietary driver
-
515 x 791 x 597 mm
Dimensions of 2 stacked LS1200 = 1 x LS2000
45 kg (99 Lb.)
2 x 4 pole (In & Loop Thru)
Baltic Birch Ply & structured black coating
2 Metal recessed pockets
Perforated steel grilles
3 steel anchor plates for flying tracks on sides
and back
Internal Steel Stand Fitting on Top (35 mm,
1"3/8) accepts a mast supporting 1 or 2 PS15's.
(20.28"x 31.14"x 23.50")