Whirlpool GLS3064RS0 Instructions D'installation page 3

The gas and electric supply should be located as shown in
"Gas and Electric Connection Locations" section so that they
are accessible without requiring removal of the cooktop.
IMPORTANT: To avoid damage, check with your builder or
cabinet supplier to make sure that the materials used will not
discolor, delaminate or sustain other damage.
Mobile Home - Additional Installation Requirements
The installation of this cooktop must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280
(formerly the Federal Standard for Mobile Home Construction and
Safety, Title 24, HUD Part 280). When such standard is not
applicable, use the Standard for Manufactured Home
Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this cooktop must conform with the
current standards CAN/CSA-A240-latest edition, or with local
codes.
Product Dimensions
30" (76.2 cm) Model
A
C
B
A. 30" (76.2 cm)
¹⁄₈
B. 20 " (51.1 cm)
²⁷⁄₃₂
C. 2 " (7.2 cm)
36" (91.4 cm) Model
A
C
B
A. 36" (91.4 cm)
B. 20
²⁷⁄₃₂
C. 2
¹⁄₈
" (51.1 cm)
" (7.2 cm)
Gas and Electric Connection Locations
C
A. Gas pressure regulator (supplied) - arrow pointed
toward cooktop
B. 3 prong grounding type outlet with correct polarity
C. 18" (45.7 cm) minimum
D. Gas shutoff valve
Installation Clearances
B
A
G
H
A. 18" (45.7 cm) minimum clearance upper cabinet to countertop
B. Cabinet
C. 30" (76.2 cm) on 30" (76.2 cm) models
36" (91.4 cm) on 36" (91.4 cm) models
D. 13" (33 cm) maximum recommended upper cabinet depth
E. 6" (15.2 cm) minimum side wall clearance
F. 30" (76.2 cm) minimum clearance between top of cooktop
platform and bottom of unprotected wood or metal cabinet
(24" [61 cm] minimum clearance if bottom of wood or metal
cabinet is protected by not less than ¹⁄₄
retardant millboard covered with not less than No. 28 MSG
"
sheet steel, 0.015 [0.04 cm] stainless steel, or 0.024
"
aluminum or 0.020 [0.05 cm] copper)
⁵⁄₁₆
G. 2 " (5.9 cm) minimum distance to rear combustible surface
³⁄₁₆
H. 3 " (8.1 cm) minimum distance to front countertop edge
³⁄₈
I. Cutout width - 29 " (74.6 cm) on 30" models; 35
on 36" models
¹⁄₂
J. Cutout depth - 19 " (49.5 cm)
NOTE: After making the countertop cutout, some installations
may require notching down the base cabinet side walls to clear
the burner box. To avoid this modification, use a base cabinet with
sidewalls wider than the cutout.
If cabinet has a drawer, a 4" (10.2 cm) depth clearance from the
countertop to the top of the drawer (or other obstruction) in base
cabinet is required. The drawer depth may need to be shortened
to avoid interfering with the regulator.
If installing a hood above the cooktop, follow the hood
instructions for dimensional clearances above the cooktop
surface.
A
B
C L
D
D
C
F
J
E
I
"
[0.6 cm] flame
"
[0.06 cm]
³⁄₈
" (89.9 cm)
3