Pneumatic Connections - Blitz TWIN LOGOS 530/270H Notice D'utilisation

GB
- For belt drive series the thermal-breaker tripped (fig. 20).
- Is there oil in the housing to ensure lubrication? (fig. 11)
- Is power supplied to the electrical line? (sockets well connected,
thermal- breaker, fuses in good condition).
Compressor not stopping
- If the compressor does not stop when maximum pressure is
reached, the tank safety valve comes into operation. To repair the
valve, contact your nearest service centre.
IMPORTANT
- Do not on any account unscrew any connection while the tank is
pressurised – always check if the tank is pressure free.
- Do not drill holes, weld or purposely deform the compressed air
tank.
- Do not do any jobs on the compressor unless you have disconnect-
ed the power plug.
- Temperature in operating ambient: 0°C +35°C.
- Do not aim jets of water or inflammable liquids on the compressor.
- Do not place inflammable objects near the compressor.
- During down-times, turn the pressure switch to position "0" (OFF).
- Never aim the air jet at people or animals (fig. 34)
- Do not transport the compressor while the tank is pressurised.
- Be careful with regard to some parts of the compressor such as the
head and delivery tubes, as they can reach high temperatures. Do
not touch these parts to avoid burns.(fig. 18 - 19)
- Transport the compressor, lifting or pulling it with the appropriate
grips or handles (fig. 4 - 6)
- Keep children and animals well away from the machine operating
area.
- If using the compressor for painting:
a) Do not work in closed environments or near to naked flames
b) Make sure there is adequate exchange of air at the place of work
c) Protect your nose and mouth with an appropriate mask. (fig. 35)
- If the electrical cable or plug are damaged, do not use the compres-
sor and contact an authorised service centre to replace the faulty el-
ement with an original spare part.
- If the compressor is located on a shelf or on a top above floor
height, t must be secured to prevent it falling while in operation.
- Do not put objects or your hands inside the protective grilles to
avoid njury to yourself or damaging the compressor. (fig. 36)
- Do not use the compressor as a blunt object toward things or ani-
mals, o avoid serious damage.
- When you have finished using the compressor, always remove the
lug from the power socket.
N.B. Two-stage compressors can be supplied on request for use up
to 4 bar. In this case:
Maximum operating pressure 14.75 bar
Minimum operating pressure 14 bar
NOTE: For the European market, the compressor tanks are manufac-
tured to meet Directive CE87/404
For the European market, the compressors are manufactured to meet
Directive 2006/42 EC.
The level of acoustic pressure can increase from 1 to 10 dB(A) ac-
cording to the place in which the compressor is installed.
HINTS FOR EFFICIENT OPERATION
- For efficient operation of the machine at full continuing load and at
maximum operating pressure, make sure the temperature of the work
environment indoors does not exceed +25°C.
- We advise you to use the compressor at 70% maximum duty per
hour at full load as this ensures efficient operation of the product
long-term.
STORING THE PACKED AND UNPACKED COMPRESSOR
For the whole time that the compressor is not used before unpacking
it, store it in a dry place at a temperature between +5°C and + 45°C
and sheltered away from weather.
For the whole time that the compressor is not used after unpacking it,
while waiting to start it up or due to production stoppages, place
sheets over it to protect it from dust, which may settle on the compo-
nents. The oil is to be replaced and the operational efficiency of the
compressor is to be checked if it is not used for long periods.
16

PNEUMATIC CONNECTIONS

Make sure you always use pneumatic tubes for compressed air with
maximum pressure characteristics that are adequate for the com-
pressor.
Do not attempt to repair tubes if faulty.
WE RESERVE THE RIGHT TO MAKE ANY MODIFICATIONS
WITHOUT PRIOR NOTICE WHENEVER NECESSARY.