Adjusting The Cutting Gear; Troubleshooting; Care And Maintenance; Storage - PrimAster PMWH 3000 Manuel D'utilisation

6.5 Adjusting the cutting gear (Fig. 8)
The anvil blade (B) should be adjusted to have a distance
of 0 to 0,50 mm from the cutting blade (A) (fig. 8). This
distance should be kept to guarantee effective operation
of the mac.
Note: Soft materials or wet twigs can get torn instead of
cut properly due to wrong adjustment. Also a blunt an-
vil blade from frequent use produces the same problem.
On the right hand side of the shredder you will find the
blade adjustment knob (6). To adjust the distance turn the
screw to the right.
1. For lighter material, you can cut through the material
completely turn the knob clockwise half a turn.
2. If you are shredding heavy materials (such as harder
or large materials) they may need to be put through
the shredder twice, to crush the material before cutting
it completely. To loosen the adjusting screw, turn the
knob (6) anti-clockwise half a turn.
3. After you have completed the adjustment, check if
the blade cuts efficiently. To avoid and damage to the
shredder make sure that the cutting blade does not
come into contact with the anvil blade.
NOTE
1. Do not allow garden waste to accumulate before
shredding as it will begin to compost, become too
damp and clog the cutting assembly. Dry material will
help most material to clear the ejection chute. Save
some dry sticks until last to help clean the blade area.
2. Frequently monitor the build up/collection of shredded
material.
3. Do not allow shredded material to build up and fill the
inside of the shredders discharge chute.
4. When the collection box is full, press the On/Off switch
to turn the garden shredder Off before emptying.
WARNING!
Do not put your hands up inside the shredder's discharge
chute to clear away shredded material while the shredder
is switched on or connected to the mains supply.
NOTE
In normal use, do not switch off the garden shredder un-
til all of the shredded material has cleared the cutter as-
sembly. If the garden shredder is switched off too quickly,
remaining pieces of material may clog the blade assembly
and stall the motor when the shredder is switched back on.

7. Troubleshooting

The motor does not run
• The overload protection has responded.
- Allow the machine to cool down for at least 1-2 min-
utes before re-starting. Push the overload switch (2).
- Set the reversing switch to position REVERSE (4).
The cutting blade rotates in the reverse direction and
release the material so that you can remove it. Press
the green START (3) button to turn on.
• Power failure
- Check the power supply cord, the plug and your
house connection fuse and RCD.
• Safety switch on the collection box not locked in position.
- Ensure collection box is in position and locked.
GB | Operating Instructions
The material to be chopped is not pulled in
• The chopping knife is running backwards.
• The material is jammed in the feeding tunnel
The material is clogging up in the feeding funnel

8. Care and maintenance

WARNING!
Before commencing cleaning and maintenance proce-
dures, make sure the garden shredder is switched off and
disconnected from the mains supply. Always wear sturdy
leather gloves when cleaning the cutter blades.
1. To ensure the best performance from the garden shred-
2. Always clean the garden shredder immediately after
3. Do not allow material to become dry and hard on any
4. Make sure that the feeder chute and the ejection chute
5. Make sure that all nuts, bolts and screws are tight and
6. Always have any damaged, or worn parts repaired, or
7. Do not use any cleaning or solvent materials as these
8. The strength of the fastening screws of the frame
9. Oil the blade after every fourth or fifth use.
CAUTION
1. Do not over tighten the plate adjustment screw and cut
2. Have your garden shredder inspected and maintained

9. Storage

In order to protect the shredder from corrosion during ex-
tended storage, apply some environmentally friendly oil
to the blade.
Make sure that the garden shredder has been thoroughly
cleaned before storing it in a clean, dry place out of the
reach of children.
GB-7
- Change the direction of rotation..
- Set the reversing switch to position (2). Pull the ma-
terial from the feeding funnel.
- Re-feed thick branches such that the chopping knife
does not immediately grasp the pre-cut notches again.
- Pull out the branches from the feeding funnel. Use
the pusher to push or loosen branches inside.
Caution! Change the direction of rotation to the
desired position after the shredder has come to
a complete standstill.
der, it must be kept clean.
use.
of the garden shredder surfaces. This will directly af-
fect the shredding performance.
are kept clean and clear of all waste material.
secure.
replaced by qualified personnel.
could cause irreparable damage to your machine.
Chemicals could destroy the artificial materials.
should be checked from time to time.
excessive aluminium off of the plate, as this will reduce
the life of your shredder.
by qualified service personnel. Do not attempt to repair
the machine unless you are qualified to do so.