Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
warranty.
•
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and
the dealer will not accept responsibility for any ensuing defects or problems.
•
A qualified technician should install and service this device.
•
Do not switch the device on immediately after it has been exposed to changes in temperature.
Protect the device against damage by leaving it switched off until it has reached room temperature.
•
This device is designed for professional use on stage, in discos, theatres, etc. The
VDPLOW1803RGB can be used outdoor with an alternating current of max. 240V AC/50Hz.
•
Lighting effects are not designed for permanent operation: regular operation breaks will prolong their
lives.
•
Use the original packaging if the device is to be transported.
•
Keep this manual for future reference.
4. Features
•
for entertainment, stage and several outdoor applications
•
stand-alone, master/slave mode and sound-activation via built-in microphone
•
with built-in programs
•
DMX-controlled via 7-11-20-29-56 channels
5. Overview
Refer to the illustrations on page 2 of this manual.
1
tricolour LED (18x)
2
power input
3
power output
4
DMX output
5
DMX input
6
mounting bracket (2x)
6. Installation
Refer to the illustrations on page 2 of this manual.
a) Overhead mounting
•
Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable
norms.
•
The construction to which the device is attached should be able to support 10 times the weight of
the device for one hour without deformation.
•
Release the hex screws to slide the mounting brackets in the desired position. Make sure the centre
of gravity of the fixture is always between the brackets. Tighten the screws firmly.
•
The installation must always be secured with a secondary attachment e.g. a safety cable.
•
Never stand directly below the device when it is being mounted, removed or serviced. Have a
qualified technician check the device once a year and once before you bring it into service.
•
Install the device in a location with few passers-by and inaccessible to unauthorised persons.
•
Overhead mounting requires extensive experience: calculating workload limits, determining the
installation material to be used... Have the material and the device itself checked regularly. Do not
attempt to install the device yourself if you lack these qualifications as improper installation may
result in serious injuries.
•
For truss-mounting, use an appropriate clamp (not incl.) and fit an M10 bolt through the centre of
the (folded) bracket.
•
Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.
b) DMX-512 connection
•
When applicable, connect an XLR cable to the female 3-pin XLR output of a controller (not incl.)
and the other side to the male 3-pin XLR input of the VDPLOW1803RGB. Multiple
VDPLOW1803RGB's can be linked through serial linking. The linking cable should be a dual core,
screened cable with XLR input and output connectors.
•
Maximum recommended serial data link distance is 500 meters (1640 ft). Maximum recommended
number of fixtures on a serial data link is 32 fixtures.
•
A DMX terminator is recommended for installations where the DMX cable has to run a long distance
or is in an electrically noisy environment (e.g. discos). The terminator prevents corruption of the
digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 120Ω
resistor between pins 2 and 3, which is then plugged into the XLR output socket of the last device
in the chain.
14.06.2011
VDPLOW1803RGB
7
display with control buttons
A
B
C
D
E
4
MENU button
ENTER button ( )
display
UP button ( )
DOWN button ( )
©Velleman nv
Publicité
Table des Matières
