Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Triton TSPS 370 Instructions D'utilisation Et Consignes De Sécurité

Product Familiarisation

Main Unit
1. Table Insert
2. Spindle Lock Nut
3. Compression Washer
4. Sanding Sleeve
5. Switch Lock
6. ON/OFF Switch
7. Table Insert & Washer Storage
8. Bench Mounting Holes
9. Sleeve & Drum Storage
10. Tilting Mechanism
11. Direction Indicator
12. Table
13. Table Stop Lock Nut
14. Table Stop Bolt
15. Table Stop
16. Angle Locking Knob
17. Motor Vents
18. Angle Indicator Screw
19. Angle Indicator
20. Angle Scale
21. Dust Port
22. Motor Vents
Parts
23. Compression Washers
24. Sanding Sleeves (5 sizes)
25. Sanding Drum (4 sizes)
26. Table Inserts (3 sizes)
27. Tilting Table Inserts (3 sizes)
28. Table Insert & Washer Storage Unit
29. Sleeve & Drum Storage Unit
30. Spindle Lock Nut

Intended Use

Bench-mounted sanding machine with a rotating and height oscillating sanding drum.
For sanding curved and straight surfaces on intricate as well as larger workpieces.
The 45° tilting table adds additional edge sanding and chamfering.

Unpacking Your Tool

• Carefully unpack and inspect your new sander. Familiarise yourself with all
its features and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are
missing or damaged, have such parts replaced before attempting to use this tool

Before Use

WARNING: Ensure the tool is disconnected from the power supply before attaching
or changing any accessories, or making any adjustments.
Assembly
• Fit the Sleeve & Drum Storage Unit (29) onto the mountings on the left side of the
spindle sander (Image C)
• Fix the Table Insert & Washer Storage Unit (28) onto the right side of the spindle sander
(Image D) by securing the pins at the base into the main body and securing at the top
with the supplied clip
Bench Mounting
If the spindle sander is to be used in a permanent position, it is recommended that you
secure it to a rigid work surface.
• Use the Bench Mounting Holes (8) in the base of the spindle sander as a template to mark
and drill four holes in your intended mounting surface (i.e. workbench). Secure the spindle
sander into position using large bolts, washers and nuts (not supplied)
• If the spindle sander is intended to be more portable, fix a board to the base which can be
easily clamped and removed from various mounting surfaces
• If using bolts make sure they are long enough to penetrate the workbench or board
sufficiently for a secure fix
Note: Use nylon insert lock nuts or spring washers in the fixings to prevent vibration from
loosening the fixings.
Note: Never use bolts that require force to push through the Bench Mounting Holes as these
may crack the plastic body as will over-tightening the fixings.
Note: If the spindle sander table is not level between the left and right side due to variations
in the workshop floor surface or work surface additional thin washers can be used to correct
this either on the left or right side of the fixings. Level variations between front and back can
be corrected using the tilt mechanism of the spindle sander.
Dust Extraction
It is recommended that the spindle sander is used with a dust extraction system for a cleaner
and safer work environment. This is especially important where the toxicity of the workpiece
is not known, i.e. older surface coatings including paint or unknown wood treatment solutions
1. Attach the hose from the dust extraction system to the Dust Port (21) and ensure
it is secure (Image F)
2. For greatest efficiency, activate the dust extraction system before turning on the
spindle sander
Selecting the right grade of sanding sleeve
• Sanding sleeves are available in a variety of different grades: coarse (80 grit),
medium (150 grit) and fine (240 grit)
• Use a coarse grit to sand down rough finishes, medium grit to smooth the work,
and fine grit to finish off
• Always use good quality sanding sleeve to maximise the quality of the finished task
• It is advisable to do a trial run on a scrap piece of material to determine the optimum
grades of sanding sleeve for a particular job. If there are still marks on your work after
sanding, try either going back to a coarser grade and sanding the marks out before
recommencing with the original choice of grit, or try using a new piece of sanding sleeve
to eliminate the unwanted marks before going on to a finer grit and finishing the job
Selecting a Table Insert
Failure to use the correct table insert with its matching sanding sleeve could result in pinched
fingers or the workpiece being pulled down between the table insert and the sanding sleeve.
• The sanding sleeve should fit snugly into the central cut-out of the table insert
• Only fit Tilting Table Inserts (27) when you are going to tilt the Table (12)
Use the 'Table Insert & Washer Size Chart' to help determine the correct table insert and
compression washer to use with each sanding sleeve.
Table Insert & Washer Size Chart
Sanding Sleeve Diameter Table Insert Size
1/2" Small
13/16" Small
1-1/8" Medium
1-9/16" Medium
2" Large
• Imperial values are approximate
Fitting a sanding sleeve
Note: All the sanding sleeves, except the smallest 1/2" sanding sleeve, fit over a matching
Sanding Drum (25).
1. Select the correct Sanding Sleeve (24) for the intended job. Select the corresponding
Sanding Drum
2. Fit the Sanding Sleeve over the Sanding Drum (Image E) so there is no overlap either
top or bottom
3. Fit the correct Compression Washer (23) as per the chart over the spindle (Image A)
4. Fit the required size Table Insert either normal or tilting (26 or 27). Use the unlock symbol
on the table to line up the legs on the underside of the Table Insert with the indentations
for the insert mounting on the Table (12) and rotate the Table Insert clockwise to the lock
position symbol. Check the Table Insert is flush with the Table
5. Fit the Sanding Sleeve with drum over the spindle. Normal practice is to put the most worn
surface of the sanding sleeve to the top so that wear is even and to maximise use of the
sanding sleeves
6. Fit the correct Compression Washer as per the chart onto the top of the drum and sleeve
7. Finally secure the assembly with the Spindle Lock Nut (2) which is screwed in
anti-clockwise not clockwise. The final assembly should be as (Image B).
Do not over-tighten
Note: If the sleeve rotates on the drum when switched on the Spindle Lock Nut has not been
sufficiently tightened to compress the drum and therefore grip the sleeve.
IMPORTANT: Do not use a sanding sleeve that is too worn. This can lead to excessive heat
build-up and damage the drum. Damaged Sanding Drums due to worn sanding sleeves will not
be covered under guarantee.
Compression Washer Size
1/2" + 2"
13/16" + 2"
13/16" + 2"
1-9/16" + 2"
2"
9
US