Technical Data; Before Putting The Machine Into Operation - EINHELL BT-MS 210 Mode D'emploi D'origine

Anleitung_BT_MS_210_SPK1:_
GB

5. Technical data

Asynchronous motor
Input power
Operating mode
Idle speed n
0
Carbide saw blade
Number of teeth
Weight
Tilting range
Mitre cuts
Sawing width at 90°
Sawing width at 45°
Sawing width at 2 x 45°
(double mitre cuts)
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level
pA
K uncertainty
pA
L sound power level
WA
K uncertainty
WA
Wear ear-muffs.
The impact of noise can cause damage to hearing.
6. Before putting the machine into
operation
The machine has to be set up in a stable
position, i.e. it has to be bolted to a workbench, a
universal stand or the like.
All the covers and safety devices have to be
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
12
28.07.2009 9:14 Uhr
the same as that for your mains.
6.1 Setting up the saw (Fig. 12)
230 V ~ 50 Hz
Screw the additional stability bar (32) to the back
1200 W
of the machine.
S1
6.2 Adjusting the saw (Fig. 1/2)
5000 rpm
To adjust the turntable (8), loosen the locking
grip (10) by approx. 2 turns, which frees the
ø210 x ø30 x 2,5 mm
turntable (8).
24
The turntable (8) has locking points at angles of
8,8 kg
0°, 15°, 22,5°, 30° and 45°. Once the turntable
(8) is engaged, the setting must be additionally
-45° / 0° / +45°
secured by tightening the locking grip (10).
0° to 45° to the left
If you need to work with any other angles, the
max. 120 x 60 mm
rotary table is fixed in position with just the
locking handle (10).
max. 80 x 65 mm
Lightly press the machine head (4) down while at
the same time pulling the retaining pin (16) out
80 x 35 mm
from the motor mounting; this causes the saw to
move down to the lower working position.
Swing up the machine head (4).
By loosening the lock screw (12), the machine
head (4) can be angled to the left up to 45°.
Check that the voltage marked on the rating
plate is the same as your mains voltage and
connect up the machine.
94,2 dB(A)
6.3 Precision adjustment of the stop rail (Fig. 5/6)
3 dB Lower the machine head (4) and fasten in place
with the safety pin (16).
107,2 dB(A)
Fasten the turntable (8) in 0° position.
3 dB
Place the 90° stop angle (a) between the blade
(5) and the stop rail (7).
Slacken the adjustment screws (28), set the stop
rail (7) to 90° in relation to the saw blade (5) and
retighten the adjustment screws (28).
6.4 Precision adjustment of the stop for 90°
cross-cuts (Fig. 6/7)
Lower the machine head (4) and fix with the lock
pin (16).
Slacken the tightening screw (12).
Place the stop angle (a) between the saw blade
(5) and the rotary table (8).
Slacken the counter nut (19) and adjust the
setting screw (29) until the angle between the
saw blade (5) and the rotary table (8) equals 90°.
Re-tighten the counter nut (19) to fix the machine
in this setting.
Finally, check the position of the angle indicator
(11). If necessary, release the pointer with a
crosstip screwdriver, move to the 0° position of
the angle scale (15) and retighten the holding
screw.
Seite 12