Layout And Items Supplied - EINHELL TE-CS 18/165 Li Traduction Du Mode D'emploi Original

Safety instructions for saws with pendulum
guard and saws with tow guard
Lower guard function
a) Check the lower guard for proper closing
before each use. Do not operate the saw
if the lower guard does not move freely
and close instantly. Never clamp or tie the
lower guard into the open position. If the
saw is accidentally dropped, the lower guard
may be bent. Raise the lower guard with the
retracting handle and make sure it moves
freely and does not touch the blade or any
other part, in all angles and depths of cut.
b) Check the operation of the lower guard
spring. If the guard and the spring are not
operating properly, they must be serviced
before use. Lower guard may operate
sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
c) The lower guard may be retracted
manually only for special cuts such as
"plunge cuts" and "compound cuts".
Raise the lower guard by the retracting
handle and as soon as the blade enters
the material, the lower guard must be
released. For all other sawing, the lower
guard should operate automatically.
d) Always observe that the lower guard is
covering the blade before placing the saw
down on bench or fl oor. An unprotected,
coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be
aware of the time it takes for the blade to stop
after switch is released.
Keep this safety information in a safe place.

2. Layout and items supplied

2.1 Layout (Fig. 1a/1b)
1. Handle
2. On/Off switch
3. Locking button for On/Off switch
4. Locking lever for cutting depth setting
5. LED lamp
6. Soleplate
7. Locking lever for miter setting
8. Locking screw for parallel stop
9. Scale for miter angle
10. Additional handle
11. Spindle lock
12. Saw blade
13. Saw blade wrench
Anl_TE_CS_18_165_Li_USA_SPK7.indb 13 Anl_TE_CS_18_165_Li_USA_SPK7.indb 13
EN
14. Connection for sawdust extractor
15. Line guide
16. Parallel stop
17. Screw for securing the saw blade
18. Flange
19. Swing guard hood
20. Lever for swing guard hood
21. Battery capacity indicator
22. Battery capacity indicator button
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
store where you made your purchase at the latest
within 5 work days after purchasing the article and
upon presentation of a valid bill of purchase.
•
Open the packaging and take out the
equipment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
present).
•
Check to see if all the items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, keep the packaging until the end
of the guarantee period.
Danger!
The equipment and packaging material are
not toys. Do not let children play with plastic
bags, plastic sheets and small parts. There is
a risk of choking and suff ocating!
•
Cordless hand-held circular saw
•
Saw blade
•
Saw blade wrench
•
Parallel stop
•
Original operating instructions
•
Safety information
Separately available accessories
18V 1.5Ah P-X-C lithium-ion battery
18V 2.0Ah P-X-C lithium-ion battery
18V 2.6Ah P-X-C Plus lithium-ion battery
18V 3.0Ah P-X-C lithium-ion battery
18V 4.0Ah P-X-C lithium-ion battery
18V 5.2Ah P-X-C Plus lithium-ion battery
18V P-X-C charger
Explore battery + charger options at
einhellUSA.com
- 13 -
23.05.2019 11:07:26 23.05.2019 11:07:26