Safety Information - Scheppach 5801402903 Traduction Des Instructions D'origine

• The safety, work and maintenance instructions
of the manufacturer as well as the technical data
given in the calibrations and dimensions must be
adhered to.
• Relevant accident prevention regulations and other,
gene rally recognized safety-technical rules must
also be adhered to.
• The machine may only be used, maintained, and
operated by persons familiar with it and instructed
in its operation and procedures. Arbitrary alterations
to the machine release the manufacturer from all
responsibility for any resulting damages.
• The machine may only be used with original
accessories and tools made by the manufacturer.
• Any other use exceeds authorization. The
manufacturer is not responsible for any damages
resulting from un authorized use; risk is the sole
responsibility of the operator.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the equipment
is used in commercial, trade or industrial businesses
or for equivalent purposes.

5. Safety information

Attention! The following basic safety measures must
be observed when using electric tools for protection
against electric shock, and the risk of injury and fire.
Read all these notices before using the electric tool
and keep the safety instructions for later reference.
Safe work
Keep the work area orderly
1
Disorder in the work area can lead to accidents.
–
Take environmental influences into account
2
Do not expose electric tools to rain.
–
Do not use electric tools in a damp or wet en-
–
vironment.
Make sure that the work area is well-illuminated.
–
Do not use electric tools where there is a risk of
–
fire or explosion.
Protect yourself from electric shock
3
Avoid physical contact with earthed parts (e.g.
–
pipes, radiators, electric ranges, cooling units).
Keep children away
4
Do not allow other persons to touch the equipment
–
or cable, keep them away from your work area.
Securely store unused electric tools
5
Unused electric tools should be stored in a dry, ele-
–
vated or closed location out of the reach of children.
Do not overload your electric tool
6
They work better and more safely in the speci-
–
fied output range.
Use the correct electric tool
7
Do not use low-output electric tools for heavy work.
–
Do not use the electric tool for purposes for
–
which it is not intended. For example, do not
use handheld circular saws for the cutting of
branches or logs.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Do not use the electric tool to cut firewood.
–
Wear suitable clothing
8
Do not wear wide clothing or jewellery, which can
–
become entangled in moving parts.
When working outdoors, anti-slip footwear is
–
recommended.
Tie long hair back in a hair net.
–
Use protective equipment
9
Wear protective goggles.
–
Wear a mask when carrying out dust-creating work.
–
Connect the dust extraction device
10
If connections for dust extraction and a collect-
–
ing device are present, make sure that they are
connected and used properly.
Operation in enclosed areas is only permitted
–
with a suitable extraction system.
Do not use the cable for purposes for which it is
11
not intended
Do not use the cable to pull the plug out of the
–
outlet. Protect the cable from heat, oil and sharp
edges.
Secure the workpiece
12
Use the clamping devices or a vice to hold the
–
workpiece in place. In this manner, it is held
more securely than with your hand.
An additional support is necessary for long
–
workpieces (table, trestle, etc.) in order to pre-
vent the machine from tipping over.
Always press the workpiece firmly against
–
the working plate and stop in order to prevent
bouncing and twisting of the workpiece.
Avoid abnormal posture
13
Make sure that you have secure footing and
–
always maintain your balance.
Avoid awkward hand positions in which a sud-
–
den slip could cause one or both hands to come
into contact with the saw blade.
Take care of your tools
14
Keep cutting tools sharp and clean in order to
–
be able to work better and more safely.
Follow the instructions for lubrication and for
–
tool replacement.
Check the connection cable of the electric tool
–
regularly and have it replaced by a recognised
specialist when damaged.
Check extension cables regularly and replace
–
them when damaged.
Keep the handle dry, clean and free of oil and
–
grease.
Pull the plug out of the outlet
15
Never remove loose splinters, chips or jammed
–
wood pieces from the running saw blade.
During non-use of the electric tool or prior to
–
maintenance and when replacing tools such as
saw blades, bits, milling heads.
Do not leave a tool key inserted
16
Before switching on, make sure that keys and
–
adjusting tools are removed.
Avoid inadvertent starting
17
Make sure that the switch is switched off when
–
plugging the plug into an outlet.
19 / 48