Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Appliance-specific safety instructions for grind-
ers
• Hold the appliance by the insulated handles as
the abrasive belt can come into contact with
its own power cable. Damage to a live wire may
make exposed metal parts of the power tool live
and could give the operator an electric shock.
m WARNING!
• Dusts from materials such as leaded paint, some
types of wood and metal can be harmful to your
health.
• Contact with or inhalation of these dusts can rep-
resent a health hazard for the person operating the
appliance and other people in the vicinity.
• Wear safety goggles and a protective dust mask!
Residual risks
Even if you use this electric power tool in ac-
cordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment's
construction and layout:
• Lung damage if no suitable protective dust mask
is used.
• Damage to hearing if no suitable ear protection
is used.
• Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.
Technical Data
Rated voltage
Rated power consump-
tion
Idling belt speed
Rated idling speed
Abrasive belt
Protection class
Noise and vibration values
The total noise values determined in accordance
with EN 60745.
sound pressure level L
pA
uncertainty K
pA
sound power level L
WA
uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Total vibration values (vector sum - three directions)
determined in accordance with EN 60745.
Vibration emission value ah = 2,19 m/s
K uncertainty = 1,5 m/s
2
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
www.scheppach.com service@scheppach.com +(49)-08223-4002-99 +(49)-08223-4002-58
220-230 V~ / 50/60 Hz
900 W
320 m/min
2500 min
-1
75 x 533 mm
II
83 dB(A)
3 dB
94 dB(A)
3 dB
2
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Before starting the equipment
Before you connect the equipment to the mains sup-
ply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making adjust-
ments to the equipment.
Installing the dust bag (Fig. 3)
Slide the dust bag (10) on to the connection for the
dust extractor (2). Follow the instructions above in re-
verse order to remove the dust bag.
The dust is extracted straight from the sanding/grind-
ing belt into the dust bag.
m Important!
For health safety reasons it is imperative that you use
a dust bag.
Changing the sanding / grinding belt (Fig. 4 / 5)
Loosen clamping screw (7) and lock nut (6).
1.
2.
Pull the base plate (8) off the device.
3.
Pull the clamping lever (13) to the outside to relieve
the tension in the sanding/grinding belt.
Pull the used sanding/grinding belt off the drive roll-
4.
ers.
Slide the new sanding/grinding belt on to the drive
5.
rollers.
6.
Ensure that the direction of the sanding/grinding
belt (arrows on the inside of the sanding/ grinding
belt) is identical to the direction of the belt sander/
grinder (arrow over the rear drive roller).
Press the clamping lever (13) to the rear to tension
7.
the sanding/grinding belt.
8.
Re-assemble all components.
Adjusting the position of the belt (Fig. 1)
Hold the belt sander/grinder with the sanding/
1.
grinding plate at the top.
Switch on the belt sander/grinder.
2.
By turning the setting screw (9) the belt position
3.
should be set so that the sanding/grinding belt is at
the center of the two drive rollers.
GB І 13
Publicité
Table des Matières
