Technical Assistance; Assembly Instructions; High Pressure Hose Supports And Acces- Sories Assembly; Set Support (Gun + Lance) And Power Cable Assembly - VITO WR1 115B PRO-POWER Mode D'emploi

EN
Use only accessories or technically
identical parts authorized by VITO for
this machine. No doing so may result
in personal injury or damage to the
machine. In case of questions or lack of
knowledge and resources, you should
contact an official distributor.

2.6 - TECHNICAL ASSISTANCE

The machine should be repaired by
the brand's technical service, or by a
qualified person, and only with original
spare parts.
3. ASSEMBLY
INSTRUCTIONS
3.1 - HIGH PRESSURE HOSE
SUPPORTS AND ACCESSORIES
ASSEMBLY (FIG. B)
1. Attach the hose support (11) to the
transport handle (5) and tighten the
fixing screws;
2. Attach the accessory supports (12,
13) to the machine and tighten the fixing
screws;
3.2 - SET SUPPORT (GUN +
LANCE) AND POWER CABLE
ASSEMBLY (FIG.C)
1. Insert the power cable support (14)
into the fixing guide;
2. Insert the set support (gun + lance)
(3) in the fixing guide;
3. Make sure that the supports are
securely fastened;
3.3 - HIGH PRESSURE HOSE
ASSEMBLY (FIG. D)
1. Insert one of the hose connecting
accessories (16) in the machine's
connecting thread (10). Tighten the
fixing thread;
2. Insert the other hose connecting
accessory in the gun's connecting
thread (15). Tighten the fixing thread;
28
Check the condition of the hose
regularly and replace it if
damaged. Do not attempt to repair the
hose.
3.4 - GUN + LANCE SET
ASSEMBLY (FIG. E)
1. Insert the lance connector (18) in the
gun fitting (17);
2. Press and rotate it counter clockwise
until the lance (2) is properly fastened;
3. Pull the lance to ensure i tis fastened;
3.5 - WATER INLET FILTER
ASSEMBLY (FIG. F)
1. Tighten the filter (9) in the machine's
water inlet thread (19);
Never operate the machine
without the water inlet filter. The
filter should always be installed to filter
out sand and other impurities that could
cause damage to the pump valves.
3.6 - CONNECTION TO THE
WATER SYSTEM (FIG. G)
1. Connect the water supply hose to a
tap;
2. Open the tap to remove any residues
that may be inside the hose. When
clean water starts running out, close
the tap;
3. In the other extremity of the hose,
install the quick connector;
4. Remove the cover in the water inlet;
5. Tighten the water inlet filter (9) in
the water inlet (19);
6. Fit the supply hose quick connector
in the water inlet filter;
The water supply should preferably be
carried out through a hose connected
to the tap of the water supply system.
It is recommended a garden hose
with ½ "diameter and with a minimum
length of 5 m.
If you want use water from
wells, tanks or other type of
water containers, you must install an
additional filter (dust filter) in the
suction to prevent the entry of sand or
other type of waste.
In any of these situations, make
sure that the inlet water pressure
is less than 7 bar.
4. OPERATING
INSTRUCTIONS
When using the pressure washer, care
must be taken in order to avoid any
accidents:
� While operating, place the machine
in a stable surface and away from the
cleaning area;
� Do not use the power cable or
pressure hose to transport the machine;
� Never operate the machine by using
repeated and quick movements of
pressing/releasing the gun trigger. This
may result in component and pressure
connections failures;
� Do not operate the machine on empty
(no water), as it will damage the pump
seals. Always turn the water on before
starting the machine;
� To prevent accidental discharge of
high pressure water, the trigger safety
lock must be engaged whenever the
machine is not in use;
� When the machine is under pressure
and the trigger is pressed, the release
of pressure may cause gun recoil.
Adopt a stable and firm posture. Hold
the gun firmly with both hands to
prevent accidents.
� Do not use the machine with other
people nearby without
equipment;
� Never point the water jet towards
people, animals, other machines and
electrical systems;
protective