Table des Matières
Publicité
TECHNICAL DATA
CORDLESS DRILL DRIVER
Production code .........................................................................
Drilling capacity in steel..............................................................
Drilling capacity in wood ............................................................
Drilling capacity in brick and tile .................................................
Wood screws (without pre-drilling) .............................................
No-load speed, 1st gear / 2nd gear ...........................................
Impact rate 1st gear / 2nd gear ..................................................
Torque * (2.0 Ah) ........................................................................
Torque * (4.0 Ah) ........................................................................
Battery voltage ...........................................................................
Drill chuck range ........................................................................
Weight according EPTA-Procedure 01/2014 (1.5 Ah / 2.0 Ah) ..
Weight according EPTA-Procedure 01/2014 (3.0 Ah / 4.0 Ah) ..
Recommended ambient operating temperature ........................
Recommended battery types .....................................................
Recommended charger .............................................................
Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) .......................
Sound power level (Uncertainty K=3dB(A)) ............................
Always wear ear protectors!
Total vibration values (vector sum in the three axes)
determined according to EN 62841.
Drilling into metal, chuck head
Vibration emission value a
...................................................
h,D
Uncertainty K ...........................................................................
Screw driving without impact, chuck head
Vibration emission value a
.....................................................
h
Uncertainty K ...........................................................................
Impact drilling into concrete, chuck head
Vibration emission value a
..................................................
h,ID
Uncertainty K ...........................................................................
Screw driving without impact, right angle head
Vibration emission value a
.....................................................
h
Uncertainty K ...........................................................................
Screw driving without impact, off set head
Vibration emission value a
.....................................................
h
Uncertainty K ...........................................................................
* Measured according to AEG standard N 877318
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized
test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of
exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for
diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may
signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched
off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator from the eff ects of vibration and/or noise such as: maintain the tool
and the accessories, keep the hands warm, organization of work patterns.
WARNING Read all safety warnings, instructions,
illustrations and specifi cations provided with this power
tool. Failure to follow all instructions listed below may result
in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
DRILL SAFETY WARNINGS
Safety instructions for all operations
Wear ear protectors when impact drilling. Exposure to
noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
Hold the power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory or
fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a "live" wire may
24
ENGLISH
BSB 18CBL
..................... 4775 00 01...
...000001-999999
...........................13 mm
...........................45 mm
...........................14 mm
.............................8 mm
....... 0-550 / 0-2100 min
-1
..........7150 / 27300 min
-1
...........................60 Nm
...........................75 Nm
...........................18 V
.....................1,5-13 mm
..........................1,8 kg
..........................2,1 kg
...................... -18...+50 °C
... L1840R, L1830R, L1820R, L1815R
......................... BL1218
........................84,5 dB (A)
........................95,5 dB (A)
..........................2,0 m/s
2
..........................1,5 m/s
2
2
..........................2,0 m/s
..........................1,5 m/s
2
........................12,4 m/s
2
..........................1,5 m/s
2
..........................1,7 m/s
2
..........................1,5 m/s
2
..........................1,8 m/s
2
..........................1,5 m/s
2
make exposed metal parts of the power tool "live" and could
give the operator an electric shock.
Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed
rated of the drill bit. At higher speeds, the bit is likely to
bend if allowed to rotate freely without contacting the
workpiece, resulting the personal injury.
Always start drilling at low speed and with the bit tip in
contact with the workpiece. At higher speeds, the bit is
likely to bend if allowed to rotate freely without contacting the
workpiece, resulting the personal injury.
Apply pressure only in direct line with the bit and do not
apply excessive pressure. Bits can bend causing breakage
or loss of control, resulting in personal injury.
SCREWDRIVER SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces,
when performing an operation where the fastener may
contact hidden wiring. Fasteners contacting a "live" wire
may make exposed metal parts of the power tool "live" and
could give the operator an electric shock.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when
working with the machine. The use of protective clothing is
recommended, such as dust mask, protective gloves, sturdy
non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to
health. Do not inhale the dust. Wear a suitable dust protection
mask.
Do not machine any materials that present a danger to health
(e.g. asbestos).
Switch the device off immediately if the insertion tool stalls!
Do not switch the device on again while the insertion tool is
stalled, as doing so could trigger a sudden recoil with a high
reactive force. Determine why the insertion tool stalled and
rectify this, paying heed to the safety instructions.
The possible causes may be:
• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use.
WARNING! Danger of burns
• when changing tools
• when setting the device down
Chips and splinters must not be removed while the machine
is running.
When working in walls ceiling, or fl oor, take care to avoid
electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped
workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the
machine.
Do not dispose of used battery packs in the household refuse
or by burning them. AEG Distributors off er to retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects
(short circuit risk).
Use only System GBS chargers for charging System GBS
battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store
only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme
load or extreme temperatures. In case of contact with battery
acid wash it off immediately with soap and water. In case of
eye contact rinse thoroughly for at least 10 minutes and
immediately seek medical attention.
ALWAYS USE A SIDE HANDLE when using a 9.0 Ah or
higher capacity battery pack; the output torque of some
tools may increase. If your drill/driver did not come with a
side handle, visit www.aeg-powertools.eu for the appropriate
accessory handle.
Do not insert the bit on tool when the tool is running, and
switch is lock on status, the bit will be run and may hurt the
user
Warning! To reduce the risk of fi re, personal injury, and
product damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to fl ow
inside them. Corrosive or conductive fl uids, such as seawater,
certain industrial chemicals, and bleach or bleach containing
products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The electronic percussion drill/screwdriver can be universally
used for drilling, percussion drilling, screwdriving and cutting
screw threads.
Do not use this product in any other way as stated for normal
use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product
described under "Technical Data" fulfi lls all the relevant
regulations and the directives 2011/65/EU (RoHS), 2014/30/
EU, 2006/42/EC, and the following harmonized standards
have been used:
EN 62841-1:2015
EN 62841-2-1:2018+A11:2019
EN 62841-2-2:2014
EN 55014-1:2017
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-04-30
Alexander Krug
Managing Director
Authorized to compile the technical fi le
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
BATTERIES
Battery packs which have not been used for some time
should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure to
heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept
clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in
accordance with local, national and international provisions
and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third
parties is subject to Dangerous Goods regulations.
Transport preparation and transport are exclusively to be
carried out by appropriately trained persons and the
process has to be accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement
within packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
ENGLISH
25
Publicité
Table des Matières
