Makita UC3030A Instructions D'emploi page 19

Saw chain oil (Fig. 38)
Use a special oil with adhesive addition for lubricating
the saw chain and bar. The adhesive addition prevents
that the oil is centrifuged too fast from the sawing
device.
Do not use mineral oils. In order to protect the
invironment the use of biologically decomposeable oil is
prescribed.
The saw chain oil sold by MAKITA, called BIOTOP,
is made of special vegetable oils and is biologically
decomposeable to 100%. BIOTOP has been granted
the "blue angel" for being particularly favourable to the
environment (RAL UZ 48).
BIOTOP oil is available in the following packing sizes to
suit your individual requirements:
1 liter order number 980 008 610
5 liters order number 980 008 611
Biologically decomposeable oil is stable only for a
limited period of time. It should be consumed within
2 years from the date of manufacture (printed on the
container). (Fig. 39)
Important note on bio-degradable chain oils
If you are not planning to use the saw again for an
extended period of time, empty the oil tank and put in a
small amount of regular engine oil (SAE 30), and then
run the saw for a time. This is necessary to flush out all
remaining bio-degradable oil from the oil tank, oil-feed
system, chain and guide bar, as many such oils tend
to leave sticky residues over time, which can cause
damage to the oil pump or other parts.
The next time you use the saw, fill the tank with
BIOTOP chain oil again. In case of damage caused by
using waste oil or unappropriate chain oil the product
guarantee will be null and void.
Your salesman will inform you about the use of chain oil.
Never use waste oil (Fig. 40)
Waste oil is very dangerous for the environment.
Waste oil contains high amounts of carcinogenic
substances.
The residues in the waste oil result in a high degree of
wear and tear at the oil pump and the sawing device.
In the case of damage caused by using waste oil or
unappropriate saw chain oil the product guarantee will
be null and void.
Your salesman will inform you about the use of saw
chain oil.
Avoid skin and eye contacts (Fig. 41)
Mineral oil products as well as oil degrease the skin.
If your skin repeatedly comes in contact with these
substances for a longer period of time, it will desiccate.
Various skin deseases may result. In addition, allergic
reactions are known.
Eyes can be irritated by contact with oil. If oil gets into
your eyes, immediately wash them with clear water. If
your eyes are still irrritated, go to see a doctor.
Refilling the oil tank (Fig. 42)
Only if the motor is switched off and the power
supply plug is pulled out!
- Thoroughly clean the oil tank around the cap to
prevent dirt from entering the tank.
- Unscrew the tank cap (1) and fill in chain oil until it is
on a level with the bottom edge of the filler socket.
- Tightly screw on the tank cap.
- Thoroughly remove any oil that has overflown.
Important! (Fig. 43)
Before operating the saw for the first time, the oil feed
system must be completely filled, until the chain oil
lubricates the chain and guide bar.
This procedure can take up to two minutes.
- The oil level can be controlled in the sight glass (2).
In order to ensure sufficient lubrication of the saw chain
there must always be enough oil in the tank.
Lubricating the saw chain (Fig. 44)
Only if the motor is switched off and the power
supply plug is pulled out!
To guarantee a troublefree operation of the oil pump the
oil guide groove (3) as well as the oil inlet bore in the
guide bar (4) must be cleaned in regular intervals.
Note:
After the saw has been turned off it is normal for
residual chain oil to drip from the oil feed system,
the guide bar and the chain for a time. This does not
constitute a defect!
Place the saw on a suitable surface.
Plug in the saw (Fig. 45)
CAREFUL!
Before connecting the saw to a source of
electricity, always make sure to check that when
the ON/OFF switch (1) has been pressed in and
released, it automatically comes back out to the
"off" position. If it does not, do not under any
circumstances connect the saw to a power source
- do not plug it in. Take the saw to a MAKITA
service centre before doing any work with it.
Clip the extension cord and the saw's power cord into
the cord grip (2).
Plug the saw plug (3) into the socket of the extension
cable (4).
Switching on the motor (Fig. 46)
- Plug in the saw (see above).
- When switching on the electric chain saw always
hold it with both hands. Take the back handle with
the right hand and the tubular handle with the left
hand. Hold the handles tightly with your thumbs facing
your fingers. The bar and chain must not be in contact
with any object.
- First depress the locking button (5) and then the
power switch (1). Then release the locking button (5).
- Attention: The chain starts running immediately.
Keep the power switch depressed as long as the
motor is to run.
CAUTION:
Never lock the power switch in the ON position.
Switching off the motor
- Release the power switch (1).
NOTE:
When the chain brake is actuated the power supply
19